GammaManager Facebook  ●  investorinfo@gammamanager.com

EBM Research & Development

Research & Development

Milestones of the EBM Clean Energy Technology Development

1983

Completed a series of tests on small rotating permanent magnet units

1985

After test results from 1983-84 were compiled and deciphered, the base differential equation was solved.

1986

Established and staffed laboratories in Canada and USA for further refinement of the differential equation, the research and procurement of materials to be tested for introduction into the continuing research and development, including state-of-the-art metals and ceramics from the Laboratories in Houston Texas.

1989

Opened laboratories in England and Hungary. Teams of engineers, physicists and design personnel were assembled and assigned the challenge to create a unique and undiscovered geometry for the stator and rotor designs to be built and make the refined differential equation a reality that could be measured.

1992

The Otto EBM Unit

Otto EBM unit
First Otto EBM

1st lab unit whose geometry showed additional torque on the shaft.

After 108 prototypes, the first EBM unit was produced in Budapest Hungary, the ‘Otto Unit’. It weighed less than 80 kg, but exhibited the desired excess torque on the shaft of the unit that the differential equation promised. With the promise of this first demo unit, the entire team was consolidated in Budapest, Hungary, to continue the research and development.

1997-2002

The BB-Lego EBM Unit

The BB-Lego EBM Unit
BB-Lego EBM

The Otto Unit led to the BB-Lego Units, in which the weight of unit was increased by a factor of 10. Two of the four BB-Lego units were 2-pole units, while the other two units were 4-pole units. The results confirmed that the unique geometry did, in fact, produce extra torque on the shaft.

The C4/4 EBM Unit

The C4/4 EBM Unit
On the 'Test Bay'
C4/4 EBM
The C4/4 EBM Unit
Experimental Rotors
C4/4 Experimental rotors

The test results of the BB-Lego Units led to C4/4 Unit. Once again, the weight of the entire unit was increased by a factor of 10, and the resulting testing data solidified the original data from the smaller units - there is unquestionably extra torque being produced.

The 720 EBM Unit

The 720 EBM Unit
In the 'Thermal Box' used to verify energy gain
720 EBM
The 720 EBM Unit
Leslie Szabó inspecting the Rotor
In the Thermal Box
The 720 EBM Unit
Outside the 'T-Box' test set up
Outside T-Box

View of the EBM 720 Unit outside of the ‘T-box’ test set up.

The 720 EBM Unit
Close up view of the control panel
Control Panel
The 720 EBM Unit
Open door view of the capacitor panel
Capacitor Panel

Another increase by a factor of 10 in the weight of the unit led to two separate units called the 720 Units, named for the diameter of their rotors being 720mm.

Three different EBM Sized prototypes were built and tested over 100,000 man-hours:

BB-LEGO - (60 W)
(4 units)
Excess could be considered as measurement error, not excess power
C4/4 - (1.5 kW)
(1 unit)
1.5 kW excess power
720 - (10 - 15 kW)
(2 units)
15 kW maximum excess power

For all tests, the thermal energy of the units were carefully measured under load, and included in the total energy produced.

2005-2006

Fourteen types of EBM Units were designed to obtain manufacturing costs. Complete sets of drawings and specifications were produced in both Hungarian and English.

2006

Statutory Declarations were obtained.

Statutory Declaration of North-American Experts

Statutory declaration N-America 1
Statutory declaration N-America 1
×
Statutory declaration N-America 2
Statutory declaration N-America 2
×

To protect the privacy of the scientists who signed the Statutory Declarations (Certifications) the following is to be strictly followed:
You may check independently the credentials of the scientists by means available to you, except: You do not contact them directly.
Thank you for your cooperation, Gamma Manager Kft., and Electro Erg. Ltd.

Statutory Declaration of European Experts

Statutory declaration EU 1
Statutory declaration Europe 1
×
Statutory declaration EU 2
Statutory declaration Europe 2
×
Statutory declaration EU 3
Statutory declaration Europe 3
×

2007-2011

Research and Development of the EBM Household Sized Units.

2012-2015

The SLIS-01A EBM Unit ‘The Red Unit’

The SLIS-01A EBM Unit
‘The Red Unit’
The Red Unit

The following EBM Household Unit was built, and its mathematical model tested:

SLIS-01A   (1.5 kW)

2015 -
Present

The SYNTECH EBM Unit

The SYNTECH EBM Unit
The Red Unit

The SYNTECH Units are composed of available manufactured synchronous motors or generators manufactured by large international companies, for example:

  • Siemens (German)
  • ABB (Swiss)
  • Mitsubishi (Japan)
  • GE (USA)
And Gamma/Electric Erg. uses them together as driving units. A three phase generator is then attached to the shaft of these to be driven by the altered driving units. This unique method reduces the cost of manufacturing and assembly of the finished EBM units.

The following EBM Unit was built, its mathematical model tested, and is ready for scaling up:

SYNTECH (12 kW at present time, eventually 25 kW - 1 MW)